Description
FO converter with integrated optical diagnostics, alarm contact, for PROFIBUS up to 12 Mbps, T-coupler with two FO interfaces (BFOC), 850 nm, for PCF/fiberglass cable (multimode)
| Utilization restriction | |
| EMC note | EMC: class A product, see manufacturer’s declaration in the download area |
| Utilization restriction | |
| CCCex note | Use in potentially explosive areas is not permitted in China. |
| Product type | Media converter |
| MTTF | 212 Years (SN 29500 standard, temperature 25°C, operating cycle 21%) |
| 150 Years (SN 29500 standard, temperature 40°C, operating cycle 34.25%) | |
| 86 Years (SN 29500 standard, temperature 40°C, operating cycle 100%) | |
| MTBF | 149 Years (Telcordia standard, 25°C temperature, 21% operating cycle (5 days a week, 8 hours a day)) |
| 24 Years (Telcordia standard, 40°C temperature, 34.25% operating cycle (5 days a week, 12 hours a day)) |
| Electrical isolation | VCC // RS-485 |
| Maximum power dissipation for nominal condition | 2.88 W |
| Test voltage data interface/power supply | 1.5 kVrms (50 Hz, 1 min.) |
| Supply | |
| Supply voltage range | 18 V DC … 30 V DC (via pluggable COMBICON screw terminal block) |
| Nominal supply voltage | 24 V DC (in acc. with UL) |
| Typical current consumption | 120 mA (24 V DC) |
| Max. current consumption | 130 mA |
| ≤ 2 A (For operation in a joining station, via the DIN rail connector) | |
| Connection method | COMBICON plug-in screw terminal block |
| Switching | |
| Output name | Relay output |
| Output description | Alarm output |
| Number of outputs | 1 |
| Maximum switching voltage | 60 V DC (Resistive Load, General Load) |
| 30 V AC (Resistive load) | |
| 42 V AC (peak, resistive load) | |
| Limiting continuous current | 0.46 A |
| Supply | |
| Connection method | COMBICON plug-in screw terminal block |
| Stripping length | 7 mm |
| Tightening torque | 0.56 Nm … 0.79 Nm |
| Bit distortion, input | ± 35 % (permitted) |
| Bit distortion, output | < 6.25 % |
| Bit delay | < 1 bit (DIP 7 = OFF, standard operation) |
| 11 bit (DIP 7 = ON, redundancy operation) | |
| Signal | PROFIBUS |
| Data: optical FO | |
| No. of channels | 2 |
| Transmit capacity, minimum | -4.2 dBm (200/230 µm) |
| -17.8 dBm (50/125 µm) | |
| -14.6 dBm (62,5/125 µm) | |
| Transmission length incl. 3 dB system reserve | 2600 m (with F-G 50/125 2.5 dB/km) |
| 3300 m (with F-G 62,5/125 3.0 dB/km) | |
| 800 m (With F-K 200/230 10 dB/km with quick mounting connector) | |
| Transmission protocol | Protocol-transparent to the RS-485 interface |
| Connection method | B-FOC (ST®) |
| Wavelength | 850 nm |
| Minimum receiver sensitivity | -30 dBm (50/125 µm) |
| Maximum receiver sensitivity | -3 dBm (200/230 µm) |
| Transmission medium | PCF fiber |
| Multi-mode fiberglass | |
| Data: PROFIBUS acc. to IEC 61158, RS-485 2-wire, half duplex, automatic control | |
| Serial transmission speed | ≤ 12 Mbps |
| Connection method | D-SUB-9 female connector |
| Transmission length | ≤ 1200 m (depending on the data rate, with shielded, twisted pair data cable) |
| Conductor cross section flexible max. | 2.5 mm² |
| Conductor cross section flexible min. | 0.2 mm² |
| Conductor cross section solid max. | 2.5 mm² |
| Conductor cross section solid min. | 0.2 mm² |
| Max. AWG conductor cross section, flexible | 14 |
| Min. AWG conductor cross section, flexible | 24 |
| Single-wire/terminal point, solid AWG max. | 14 |
| Single-wire/terminal point, solid AWG min. | 24 |
| Transmission medium | Copper |
| File format/coding | UART (11 Bit, NRZ) |
| Data direction switching | Automatic control |
| Output nominal voltage | 5 V ±0.25 (50 mA) |
| Width | 35 mm |
| Height | 99 mm |
| Depth | 106 mm |
| Material | PA 6.6-FR (Housing) |
| FO cable | |
| Fiber types | 50/125 µm |
| 62.5/125 µm | |
| Fiberglass | |
| Ambient conditions | |
| Degree of protection | IP20 |
| Ambient temperature (operation) | -20 °C … 60 °C |
| Ambient temperature (storage/transport) | -40 °C … 85 °C |
| Altitude | ≤ 5000 m (For restrictions, see the manufacturer’s declaration for altitude operation) |
| ≤ 2000 m (Hazardous locations) | |
| Permissible humidity (operation) | 30 % … 95 % (non-condensing) |
| CE | |
| Certificate | CE-compliant |
| EAC | |
| Identification | EAC |
| ATEX | |
| Identification | II 3 G Ex nA nC IIC T4 Gc X |
| Note | Please follow the special installation instructions in the documentation! |
| ATEX, FO interface | |
| Identification | II (2) G [Ex op is Gb] IIC |
| II (2) D [Ex op is Db] IIIC | |
| Certificate | PTB 06 ATEX 2042 U |
| Note | Please follow the special installation instructions in the documentation! |
| UL, USA / Canada | |
| Identification | Class I, Zone 2, AEx nc IIC T5 |
| Class I, Zone 2, Ex nC nL IIC T5 X | |
| Class I, Div. 2, Groups A, B, C, D | |
| PROFIBUS interoperability | |
| Note | Tested by independent PNO test laboratory (PN059-485-01) |
| ABB certification | |
| Identification | IndustrialIT enabled |
| Note | This certification is a trademark of ABB. |
| Corrosive gas test | |
| Identification | ISA-S71.04-1985 G3 Harsh Group A |
| Shipbuilding | |
| Identification | DNV GL |
| DNV GL data | |
| Temperature | B |
| Humidity | A |
| Vibration | A |
| EMC | B |
| Enclosure | Required protection according to the Rules shall be provided upon installation on board |
| Electromagnetic compatibility | Conformance with EMC Directive 2014/30/EU |
| Noise emission | EN 55011 |
| Noise immunity | EN 61000-6-2:2005 |
| Electrostatic discharge | |
| Standards/regulations | EN 61000-4-2 |
| Electrostatic discharge | |
| Contact discharge | ± 6 kV |
| Discharge in air | ± 8 kV |
| Comments | Criterion B |
| Electromagnetic HF field | |
| Standards/regulations | EN 61000-4-3 |
| Electromagnetic HF field | |
| Field intensity | 10 V/m |
| Comments | Criterion A |
| Fast transients (burst) | |
| Standards/regulations | EN 61000-4-4 |
| Fast transients (burst) | |
| Input | ± 2 kV |
| Signal | ± 2 kV |
| Comments | Criterion B |
| Surge current load (surge) | |
| Standards/regulations | EN 61000-4-5 |
| Surge current load (surge) | |
| Input | ± 0.5 kV |
| Signal | ± 1 kV |
| Comments | Criterion B |
| Conducted interference | |
| Standards/regulations | EN 61000-4-6 |
| Conducted interference | |
| Comments | Criterion A |
| Voltage | 10 V |
| Emitted interference | |
| Standards/regulations | EN 55011 |
| Comments | Class A, industrial applications |
| Criteria | |
| Criterion A | Normal operating behavior within the specified limits. |
| Criterion B | Temporary impairment to operational behavior that is corrected by the device itself. |
| Free from substances that could impair the application of coating | in accordance with VW-AUDI-Seat central standard P-VW 3.10.7 57 65 0 |
| Air clearances and creepage distances | |
| Standards/regulations | DIN EN 60664-1 |
| VDE 0110-1 | |
| DIN EN 50178 | |
| EN 60950 | |
| Mounting type | DIN rail mounting |
| Item number | 2708261 |
| Packing unit | 1 pc |
| Minimum order quantity | 1 pc |
| Sales Key | DNC |
| Product Key | DNC211 |
| Catalog Page | Page 431 (C-6-2019) |
| GTIN | 4017918973964 |
| Weight per Piece (including packing) | 265.2 g |
| Weight per Piece (excluding packing) | 265.2 g |
| Customs tariff number | 85176200 |
| Country of origin | DE |
ECLASS
| ECLASS-9.0 | 19170114 |
| ECLASS-10.0.1 | 19170132 |
| ECLASS-11.0 | 19170411 |
ETIM
| ETIM 8.0 | EC001467 |
UNSPSC
| UNSPSC 21.0 | 43201500 |
Can be combined with the PSI copper repeater in a modular way using DIN rail connectors|Supply voltage and data signals routed through the DIN rail connectors|Connections can be plugged in via a COMBICON screw terminal block|Automatic data rate detection or fixed data rate setting via DIP switches|Redundant power supply|High-quality electrical isolation between all interfaces (PROFIBUS // fiber optic ports // power supply // DIN rail connector)|Approved for use in zone 2|Integrated optical diagnostics for continuous monitoring of FO paths|Intrinsically safe fiber optic interface (Ex op is) for direct connection to devices in zone 1|Floating switch contact for advance warning of critical FO paths|Suitable for all data rates up to 12 Mbps|Bit retiming for any cascading depth|Shipbuilding approval in accordance with DNV GL
