Description

PN-,25-REN14-MFRKG/US/ /V

Product characteristics Number of inputs and outputs Number of digital outputs: 2; Number of analogue outputs: 1 Measuring range

-0.0125…0.25 bar

-12.5…250 mbar

-5…100.4 inH2O

-1.25…25 kPa

-127…2549 mmWS

Process connection threaded connection 1/4″ NPT internal thread Application Special feature Gold-plated contacts Measuring element ceramic-capacitive pressure measuring cell Application for industrial applications Media liquids and gases Medium temperature [°C] -25…80 Min. bursting pressure

30000 mbar

12000 inH2O

3000 kPa

306000 mmWS

Pressure rating

10000 mbar

4000 inH2O

1000 kPa

102000 mmWS

Vacuum resistance [mbar] -1000 Type of pressure relative pressure MAWP (for applications according to CRN)

10 bar

10000 mbar

4000 inH2O

1000 kPa

Electrical data Operating voltage [V] 18…30 DC; (to SELV/PELV) Current consumption [mA] < 35 Min. insulation resistance [MΩ] 100; (500 V DC) Protection class III Reverse polarity protection yes Power-on delay time [s] 0.3 Integrated watchdog yes Inputs / outputs Number of inputs and outputs Number of digital outputs: 2; Number of analogue outputs: 1 Outputs Total number of outputs 2 Output signal switching signal; analogue signal; IO-Link; (configurable) Electrical design PNP/NPN Number of digital outputs 2 Output function normally open / normally closed; (parameterisable) Max. voltage drop switching output DC [V] 2 Permanent current rating of switching output DC [mA] 250 Switching frequency DC [Hz] < 500 Number of analogue outputs 1 Analogue current output [mA] 4…20; (scalable 1:5) Max. load [Ω] 500 Analogue voltage output [V] 0…10; (scalable 1:5) Min. load resistance [Ω] 2000 Short-circuit protection yes Type of short-circuit protection pulsed Overload protection yes Measuring/setting range Measuring range

-0.0125…0.25 bar

-12.5…250 mbar

-5…100.4 inH2O

-1.25…25 kPa

-127…2549 mmWS

Analogue start point

-12.5…200 mbar

-5…80.2 inH2O

-1.25…20 kPa

-125…2040 mmWS

Analogue end point

37.5…250 mbar

15…100.4 inH2O

3.75…25 kPa

385…2550 mmWS

Factory setting / CMPT = 2 Set point SP

-11…250 mbar

-4.4…100.4 inH2O

-1.1…25 kPa

-110…2550 mmWS

Reset point rP

-12…249 mbar

-4.8…100 inH2O

-1.2…24.9 kPa

-120…2540 mmWS

Min. difference between SP and rP

1.5 mbar

0.6 inH2O

0.15 kPa

15 mmWS

In steps of

0.5 mbar

0.2 inH2O

0.05 kPa

5 mmWS

Status_B High Resolution / CMPT = 3 Set point SP

-10.9…250 mbar

-4.4…100.4 inH2O

-1.09…25 kPa

-112…2550 mmWS

Reset point rP

-12…249 mbar

-4.8…100 inH2O

-1.2…24.9 kPa

-122…2539 mmWS

Min. difference between SP and rP

1.1 mbar

0.5 inH2O

0.11 kPa

11 mmWS

In steps of

0.1 mbar

0.1 inH2O

0.01 kPa

1 mmWS

Accuracy / deviations Switch point accuracy [% of the span] < ± 0,4; (Turn down 1:1) Repeatability [% of the span] < ± 0,1; (with temperature fluctuations < 10 K; Turn down 1:1) Characteristics deviation [% of the span] < ± 0,25 (BFSL) / < ± 0,5 (LS); (Turn down 1:1; BFSL = Best Fit Straight Line; LS = limit value setting) Hysteresis deviation [% of the span] < ± 0,1; (Turn down 1:1) Long-term stability [% of the span] < ± 0,05; (Turn down 1:1; per 6 months) Temperature coefficient zero point [% of the span / 10 K] < ± 0,2; (-0…80 °C) Temperature coefficient span [% of the span / 10 K] < ± 0,2; (-0…80 °C) Notes on the accuracy / deviation switch point accuracy, linearity error under DNV GL: < ± 1%: < ± 1% Response times Response time [ms] < 1.5 Delay time programmable dS, dr [s] 0…50 Damping process value dAP [s] 0…4 Damping for the analogue output dAA [s] 0…4 Max. response time analogue output [ms] 3 Software / programming Parameter setting options hysteresis / window; normally open / normally closed; switch-on/switch-off delay; Damping; Display unit; current/voltage output Interfaces Communication interface IO-Link Transmission type COM2 (38,4 kBaud) IO-Link revision 1.1 SDCI standard IEC 61131-9 SIO mode yes Required master port type A; (wenn PIN 2 nicht verbunden: B) Supported DeviceIDs

Type of operation	DeviceID
Factory setting / CMPT = 2	476
Status_B High Resolution / CMPT = 3	992

Note

For further information please see the IODD PDF file under “Downloads”

Factory setting / CMPT = 2 Profiles Smart Sensor: Process Data Variable; Device Identification, Device Diagnosis Min. process cycle time [ms] 2.3 IO-Link resolution pressure [mbar] 0.1 IO-Link process data (cyclical)

function	bit length
pressure	14
binary switching information	2

IO-Link functions (acyclical) application specific tag Status_B High Resolution / CMPT = 3 Profiles Smart Sensor ED2: Digital Measuring Sensor (0x000A), Identification and Diagnosis (0x4000) Min. process cycle time [ms] 3 IO-Link resolution pressure [mbar] 0.1 IO-Link process data (cyclical)

function	bit length
pressure	16
device status	4
binary switching information	2

IO-Link functions (acyclical) application specific tag Operating conditions Ambient temperature [°C] -25…80 Storage temperature [°C] -40…100 Protection IP 65; IP 67 Tests / approvals EMC

DIN EN 61000-6-2
DIN EN 61000-6-3

Shock resistance

DIN EN 60068-2-27

50 g (11 ms)

Vibration resistance

DIN EN 60068-2-6

20 g (10…2000 Hz)

MTTF [years] 145 UL approval

UL Approval no.

J012

Pressure Equipment Directive Sound engineering practice; can be used for group 2 fluids; group 1 fluids on request Mechanical data Weight [g] 223.5 Materials stainless steel (1.4404 / 316L); PBT+PC-GF30; PBT-GF20; PC Materials (wetted parts) stainless steel (1.4404 / 316L); AI2O3 (96%; ceramics); FKM Min. pressure cycles 100 million Tightening torque [Nm] > 50; (depends on lubrication, seal and pressure rating) Process connection threaded connection 1/4″ NPT internal thread Restrictor element integrated no (can be retrofitted) Displays / operating elements Display

Display unit	4 x LED, green (mbar, mmWS, kPa, inH2O)
switching status	2 x LED, yellow
measured values	alphanumeric display, red/green 4-digit

Remarks Pack quantity 1 pcs. Electrical connection Connection Connector: 1 x M12; coding: A; Contacts: gold-plated